RQVMM-3020全自动快速拼接测量仪技术参数
RQVMQ-50RQVMQ系列闪测仪技术参数
RQLMV-MU-6050/T龙门式影像测量仪技术参数
RQVMM-3020/T高精度全自动型影像测量仪技术参数
RQCNC-3020/T全自动型影像测量仪技术参数
RQDZX-3020/TZ轴自动型影像测量仪技术参数
RQDX-3020/T手动型影像测量仪技术参数
没有匹配的机型,换个关键词或直接联系工程师。
技术资料
六份技术文件,覆盖原理到验收
行业案例
典型检测工况,以及本产品线对应的解决思路。
01
工况五金冲压
检测难点冲压件轮廓尺寸
解决方案200×150mm 视野,±2μm
结果出具检测报告;按标准核验示值误差与重复性。
02
工况医疗器械
检测难点注射器针管
解决方案全自动批量,CPK ≥1.33
结果出具检测报告;按标准核验示值误差与重复性。
03
工况连接器
检测难点0.5mm 节距端子
解决方案多段编程,一次测 40 点
结果出具检测报告;按标准核验示值误差与重复性。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
产品原理
从物理效应到测量结果,讲清设备的工作原理。
原理要点
- 工件经均匀背光或同轴光照明,相机采集边缘图像,通过亚像素边缘提取算法定位轮廓点,再由像素当量换算为实际尺寸
- 三轴(含 Z 轴)机型可做高度与台阶测量
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
动图流程
标准作业顺序,并标出最易引入误差的关键步骤。
01放置工件并找正 →
02建立坐标系 →
03选择测量元素(点/线/圆/弧) →关键控制点
04自动抓边 →关键控制点
05计算尺寸与公差判定 →
06导出检测报告
参考耗时 — 单件典型耗时 3–15 分钟;高亮步骤是测量误差的主要来源。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
标准规范
涉及方法、检定与验收的国家标准与国际标准。
| 标准编号 | 适用范围 |
|---|---|
— | JJF 1318-2011 影像测量仪校准规范 |
GB/T 24762 | 产品几何技术规范(GPS) 影像测量 |
ISO 10360-7 | 坐标测量机验收检测(CMM 配影像探头) |
常见问题
Which standards apply?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
选型方案
按工况对应推荐系列,再与工程师确认具体配置。
工况推荐系列选型理由
按行程选 200×150 / 300×200 / 400×300mm以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
高精度选远心镜头+光栅尺以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
批量检测选自动程控机型+自动上下料以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
需测高度选带 Z 轴与激光/接触测头机型。以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
检测方法
取样、制样、检测、复核与验收判据。
标准作业流程
- 用标准玻璃刻线尺校准 XY 示值误差,用标准圆/角度块校准圆度与角度示值
- 定期检查光源均匀性与镜头畸变校正参数
验收判据
用标准块间接检定:工作面均布不少于 5 点,示值误差与重复性需满足相应检定规程。
注意事项
班前用标准块校验,保持压头与试样表面清洁,测量系统定期用标准刻线尺校准。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.