中国(上海)自由贸易试验区临港新片区老芦公路536号
021-57525860·13162862074
首页/产品目录/三坐标测量机
08 / 16 · 产品线

三坐标测量机Coordinate Measuring Machines

三坐标测量机通过测头在 X/Y/Z 三轴上的精密位移,采集工件表面点坐标,由软件拟合几何元素并评价尺寸与形位公差,是机械制造中最通用的三维测量基准设备。

14款机型
1类型
GBISO · ASTM
48h技术响应
14 款机型
共 14 款机型 · 产品线⚡ 快速选型向导⌕ 产品选型中心¥ 报价申请与选型方案▤ 选型方案↓ 选型方案书
没有匹配的机型,换个关键词或直接联系工程师。

技术资料

六份技术文件,覆盖原理到验收

行业案例

典型检测工况,以及本产品线对应的解决思路。

01
工况汽车动力
检测难点缸体孔位与平面度
解决方案1.8μm+L/350,自动换测头
结果出具检测报告;按标准核验示值误差与重复性。
02
工况航空制造
检测难点叶片型面
解决方案扫描测头,型面公差 ±0.03mm
结果出具检测报告;按标准核验示值误差与重复性。
03
工况模具
检测难点型腔轮廓
解决方案激光扫描 + 点云比对
结果出具检测报告;按标准核验示值误差与重复性。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

产品原理

从物理效应到测量结果,讲清设备的工作原理。

压头物镜试样光源数据处理
原理要点
  1. 以高精度光栅尺为长度基准,气浮导轨保证运动直线度
  2. 接触式测头触发瞬间记录三轴坐标,软件以最小二乘法拟合平面、圆、圆柱、圆锥等要素,再按图纸公差评价尺寸与形位误差
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

动图流程

标准作业顺序,并标出最易引入误差的关键步骤。

01恒温并清洁工件 →
02装夹与找正 →
03建立工件坐标系 →关键控制点
04测点采集(手动/CNC) →关键控制点
05拟合评价 →
06输出报告与偏差色谱

参考耗时 — 单件典型耗时 3–15 分钟;高亮步骤是测量误差的主要来源。

常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

标准规范

涉及方法、检定与验收的国家标准与国际标准。

标准编号适用范围
GB/T 16857.2坐标测量机的验收检测(ISO 10360-2)
GB/T 1958产品几何技术规范 几何公差检测
—JJF 1064 坐标测量机校准规范
常见问题
Which standards apply?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

选型方案

按工况对应推荐系列,再与工程师确认具体配置。

工况推荐系列选型理由
按工件尺寸选行程(500×700×500 至 2000×3000×1500)以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
车间现场选温度补偿型或花岗岩高刚性结构以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
精密计量选高精度气浮机型以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
复杂曲面选扫描测头/激光扫描。以上参数仅供参考,最终配置、价格与交期以正式报价单为准。
常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.

检测方法

取样、制样、检测、复核与验收判据。

标准作业流程
  1. 用标准球、量块、步距规按 ISO 10360-2 检测示值误差与探测误差
  2. 每日开机用标准球做测头校验,记录环境温度与湿度
验收判据

用标准块间接检定:工作面均布不少于 5 点,示值误差与重复性需满足相应检定规程。

注意事项

班前用标准块校验,保持压头与试样表面清洁,测量系统定期用标准刻线尺校准。

常见问题
How do I choose the right configuration?
Send us the specimen material, dimensions and applicable standard; an engineer will propose the model and fixturing, and provide a written selection proposal.
Are the published specifications final?
They are reference values for the standard configuration. Final configuration, price and lead time are stated in the formal quotation.
Do you support sample testing?
Yes. Send samples for measurement; we provide a test report together with the recommended configuration.
咨询热线